//////////////////////////////////////////////////////////////////////
////                                                              ////
////  uart_regs.v                                                 ////
////                                                              ////
////                                                              ////
////  This file is part of the "UART 16550 compatible" project    ////
////  http://www.opencores.org/cores/uart16550/                   ////
////                                                              ////
////  Documentation related to this project:                      ////
////  - http://www.opencores.org/cores/uart16550/                 ////
////                                                              ////
////  Projects compatibility:                                     ////
////  - WISHBONE                                                  ////
////  RS232 Protocol                                              ////
////  16550D uart (mostly supported)                              ////
////                                                              ////
////  Overview (main Features):                                   ////
////  Registers of the uart 16550 core                            ////
////                                                              ////
////  Known problems (limits):                                    ////
////  Inserts 1 wait state in all WISHBONE transfers              ////
////                                                              ////
////  To Do:                                                      ////
////  Nothing or verification.                                    ////
////                                                              ////
////  Author(s):                                                  ////
////      - gorban@opencores.org                                  ////
////      - Jacob Gorban                                          ////
////      - Igor Mohor (igorm@opencores.org)                      ////
////                                                              ////
////  Created:        2001/05/12                                  ////
////  Last Updated:   (See log for the revision history           ////
////                                                              ////
////                                                              ////
//////////////////////////////////////////////////////////////////////
////                                                              ////
//// Copyright (C) 2000, 2001 Authors                             ////
////                                                              ////
//// This source file may be used and distributed without         ////
//// restriction provided that this copyright statement is not    ////
//// removed from the file and that any derivative work contains  ////
//// the original copyright notice and the associated disclaimer. ////
////                                                              ////
//// This source file is free software; you can redistribute it   ////
//// and/or modify it under the terms of the GNU Lesser General   ////
//// Public License as published by the Free Software Foundation; ////
//// either version 2.1 of the License, or (at your option) any   ////
//// later version.                                               ////
////                                                              ////
//// This source is distributed in the hope that it will be       ////
//// useful, but WITHOUT ANY WARRANTY; without even the implied   ////
//// warranty of MERCHANTABILITY or FITNESS FOR A PARTICULAR      ////
//// PURPOSE.  See the GNU Lesser General Public License for more ////
//// details.                                                     ////
////                                                              ////
//// You should have received a copy of the GNU Lesser General    ////
//// Public License along with this source; if not, download it   ////
//// from http://www.opencores.org/lgpl.shtml                     ////
////                                                              ////
//////////////////////////////////////////////////////////////////////
//
// CVS Revision History
//
// $Log: not supported by cvs2svn $
// Revision 1.16  2001/11/02 09:55:16  mohor
// no message
//
// Revision 1.15  2001/10/31 15:19:22  gorban
// Fixes to break and timeout conditions
//
// Revision 1.14  2001/10/29 17:00:46  gorban
// fixed parity sending and tx_fifo resets over- and underrun
//
// Revision 1.13  2001/10/20 09:58:40  gorban
// Small synopsis fixes
//
// Revision 1.12  2001/10/19 16:21:40  gorban
// Changes data_out to be synchronous again as it should have been.
//
// Revision 1.11  2001/10/18 20:35:45  gorban
// small fix
//
// Revision 1.10  2001/08/24 21:01:12  mohor
// Things connected to parity changed.
// Clock devider changed.
//
// Revision 1.9  2001/08/23 16:05:05  mohor
// Stop bit bug fixed.
// Parity bug fixed.
// WISHBONE read cycle bug fixed,
// OE indicator (Overrun Error) bug fixed.
// PE indicator (Parity Error) bug fixed.
// Register read bug fixed.
//
// Revision 1.10  2001/06/23 11:21:48  gorban
// DL made 16-bit long. Fixed transmission/reception bugs.
//
// Revision 1.9  2001/05/31 20:08:01  gorban
// FIFO changes and other corrections.
//
// Revision 1.8  2001/05/29 20:05:04  gorban
// Fixed some bugs and synthesis problems.
//
// Revision 1.7  2001/05/27 17:37:49  gorban
// Fixed many bugs. Updated spec. Changed FIFO files structure. See CHANGES.txt file.
//
// Revision 1.6  2001/05/21 19:12:02  gorban
// Corrected some Linter messages.
//
// Revision 1.5  2001/05/17 18:34:18  gorban
// First 'stable' release. Should be sythesizable now. Also added new header.
//
// Revision 1.0  2001-05-17 21:27:11+02  jacob
// Initial revision
//
//

// synopsys translate_off
`include "timescale.v"
// synopsys translate_on

`include "uart_defines.v"

`define UART_DL1 7:0
`define UART_DL2 15:8

module uart_regs (clk,
	wb_rst_i, wb_addr_i, wb_dat_i, wb_dat_o, wb_we_i, wb_re_i, 

// additional signals
	modem_inputs,
	stx_pad_o, srx_pad_i,
	rts_pad_o, dtr_pad_o, int_o
	);

input 									clk;
input 									wb_rst_i;
input [`UART_ADDR_WIDTH-1:0] 		wb_addr_i;
input [7:0] 							wb_dat_i;
output [7:0] 							wb_dat_o;
input 									wb_we_i;
input 									wb_re_i;

output 									stx_pad_o;
input 									srx_pad_i;

input [3:0] 							modem_inputs;
output 									rts_pad_o;
output 									dtr_pad_o;
output 									int_o;

wire [3:0] 								modem_inputs;
reg 										enable;
wire 										stx_pad_o;		// received from transmitter module
wire 										srx_pad_i;

reg [7:0] 								wb_dat_o;

wire [`UART_ADDR_WIDTH-1:0] 		wb_addr_i;
wire [7:0] 								wb_dat_i;


reg [3:0] 								ier;
reg [3:0] 								iir;
reg [1:0] 								fcr;  /// bits 7 and 6 of fcr. Other bits are ignored
reg [4:0] 								mcr;
reg [7:0] 								lcr;
reg [7:0] 								msr;
reg [15:0] 								dl;  // 32-bit divisor latch
reg 										start_dlc; // activate dlc on writing to UART_DL1
reg 										lsr_mask_d; // delay for lsr_mask condition
reg 										msi_reset; // reset MSR 4 lower bits indicator
reg 										threi_clear; // THRE interrupt clear flag
reg [15:0] 								dlc;  // 32-bit divisor latch counter
reg 										int_o;

reg [3:0] 								trigger_level; // trigger level of the receiver FIFO
reg 										rx_reset;
reg 										tx_reset;

wire 										dlab;			   // divisor latch access bit
wire 										cts_pad_i, dsr_pad_i, ri_pad_i, dcd_pad_i; // modem status bits
wire 										loopback;		   // loopback bit (MCR bit 4)
wire 										cts, dsr, ri, dcd;	   // effective signals (considering loopback)
wire 										rts_pad_o, dtr_pad_o;		   // modem control outputs

// LSR bits wires and regs
wire [7:0] 								lsr;
wire 										lsr0, lsr1, lsr2, lsr3, lsr4, lsr5, lsr6, lsr7;
reg										lsr0r, lsr1r, lsr2r, lsr3r, lsr4r, lsr5r, lsr6r, lsr7r;
wire 										lsr_mask; // lsr_mask

//
// ASSINGS
//

assign 									lsr[7:0] = { lsr7r, lsr6r, lsr5r, lsr4r, lsr3r, lsr2r, lsr1r, lsr0r };

assign 									{cts_pad_i, dsr_pad_i, ri_pad_i, dcd_pad_i} = modem_inputs;
assign 									{cts, dsr, ri, dcd} = loopback ? {mcr[`UART_MC_RTS],mcr[`UART_MC_DTR],mcr[`UART_MC_OUT1],mcr[`UART_MC_OUT2]}
											: ~{cts_pad_i,dsr_pad_i,ri_pad_i,dcd_pad_i};

assign 									dlab = lcr[`UART_LC_DL];
assign 									loopback = mcr[4];

// assign modem outputs
assign 									rts_pad_o = mcr[`UART_MC_RTS];
assign 									dtr_pad_o = mcr[`UART_MC_DTR];

// Interrupt signals
wire 										rls_int;  // receiver line status interrupt
wire 										rda_int;  // receiver data available interrupt
wire 										ti_int;   // timeout indicator interrupt
wire										thre_int; // transmitter holding register empty interrupt
wire 										ms_int;   // modem status interrupt

// FIFO signals
reg 										tf_push;
reg 										rf_pop;
wire [`UART_FIFO_REC_WIDTH-1:0] 	rf_data_out;
wire 										rf_error_bit; // an error (parity or framing) is inside the fifo
wire [`UART_FIFO_COUNTER_W-1:0] 	rf_count;
wire [`UART_FIFO_COUNTER_W-1:0] 	tf_count;
wire [2:0] 								state;
wire [9:0] 								counter_t;
wire [7:0] 								counter_b;


// Transmitter Instance
uart_transmitter transmitter(clk, wb_rst_i, lcr, tf_push, wb_dat_i, enable, stx_pad_o, state, tf_count, tx_reset, lsr_mask);

// Receiver Instance
uart_receiver receiver(clk, wb_rst_i, lcr, rf_pop, srx_pad_i, enable, rda_int,
	counter_t, counter_b, rf_count, rf_data_out, rf_error_bit, rf_overrun, rx_reset, lsr_mask);


always @(posedge clk or posedge wb_rst_i)   // synchrounous reading
begin
    if (wb_rst_i)
    begin
	wb_dat_o <= #1 8'b0;
    end
    else
    if (wb_re_i)   //if (we're not writing)
	case (wb_addr_i)
	`UART_REG_RB : if (dlab) // Receiver FIFO or DL byte 1
			wb_dat_o <= #1 dl[`UART_DL1];
		  else
			wb_dat_o <= #1 rf_data_out[9:2];
	`UART_REG_IE	: wb_dat_o <= #1 dlab ? dl[`UART_DL2] : ier;
	`UART_REG_II	: wb_dat_o <= #1 {4'b1100,iir};
	`UART_REG_LC	: wb_dat_o <= #1 lcr;
	`UART_REG_LS	: wb_dat_o <= #1 lsr;
	`UART_REG_MS	: wb_dat_o <= #1 msr;
	default:  wb_dat_o <= #1 8'b0; // ??
	endcase // case(wb_addr_i)
    else
	wb_dat_o <= #1 8'b0;
end // always @ (posedge clk or posedge wb_rst_i)

// rf_pop signal handling
always @(posedge clk or posedge wb_rst_i)
begin
	if (wb_rst_i)
		rf_pop <= #1 0; 
	else
	if (rf_pop)	// restore the signal to 0 after one clock cycle
		rf_pop <= #1 0;
	else
	if (wb_re_i && wb_addr_i == `UART_REG_RB && !dlab)
		rf_pop <= #1 1; // advance read pointer
end

wire 	lsr_mask_condition;
wire 	iir_read;
wire  msr_read;
wire	fifo_read;
wire	thre_write;

assign lsr_mask_condition = (wb_re_i && wb_addr_i == `UART_REG_LS && !dlab);
assign iir_read = (wb_re_i && wb_addr_i == `UART_REG_II && !dlab);
assign msr_read = (wb_re_i && wb_addr_i == `UART_REG_MS && !dlab);
assign fifo_read = (wb_re_i && wb_addr_i == `UART_REG_RB && !dlab);
assign thre_write = (wb_we_i && wb_addr_i == `UART_REG_TR && !dlab);

// lsr_mask_d delayed signal handling
always @(posedge clk or posedge wb_rst_i)
begin
	if (wb_rst_i)
		lsr_mask_d <= #1 0;
	else // reset bits in the Line Status Register
		lsr_mask_d <= #1 lsr_mask_condition;
end

// lsr_mask is rise detected
assign lsr_mask = lsr_mask_condition && ~lsr_mask_d;

// msi_reset signal handling
always @(posedge clk or posedge wb_rst_i)
begin
	if (wb_rst_i)
		msi_reset <= #1 0;
	else
	if (msi_reset)
		msi_reset <= #1 0;
	else
	if (wb_re_i && wb_addr_i == `UART_REG_MS)
		msi_reset <= #1 1; // reset bits in Modem Status Register
end

// threi_clear signal handling
always @(posedge clk or posedge wb_rst_i)
begin
	if (wb_rst_i)
		threi_clear <= #1 0;
	else
	if (!lsr[`UART_LS_TFE] && (tf_count==0)) // reset clear flag when tx fifo clears
		threi_clear <= #1 0;
	else
	if (wb_re_i && wb_addr_i == `UART_REG_II)
		threi_clear <= #1 1; // reset bits in Modem Status Register
end

//
//   WRITES AND RESETS   //
//
// Line Control Register
always @(posedge clk or posedge wb_rst_i)
	if (wb_rst_i)
		lcr <= #1 8'b00000011; // 8n1 setting
	else
	if (wb_we_i && wb_addr_i==`UART_REG_LC)
		lcr <= #1 wb_dat_i;

// Interrupt Enable Register or UART_DL2
always @(posedge clk or posedge wb_rst_i)
	if (wb_rst_i)
	begin
		ier <= #1 4'b0000; // no interrupts after reset
		dl[`UART_DL2] <= #1 8'b0;
	end
	else
	if (wb_we_i && wb_addr_i==`UART_REG_IE)
		if (dlab)
		begin
			dl[`UART_DL2] <= #1 wb_dat_i;
		end
		else
			ier <= #1 wb_dat_i[3:0]; // ier uses only 4 lsb


// FIFO Control Register and rx_reset, tx_reset signals
always @(posedge clk or posedge wb_rst_i)
	if (wb_rst_i) begin
		fcr <= #1 2'b11; 
		rx_reset <= #1 0;
		tx_reset <= #1 0;
	end else
	if (wb_we_i && wb_addr_i==`UART_REG_FC) begin
		fcr <= #1 wb_dat_i[7:6];
		rx_reset <= #1 wb_dat_i[1];
		tx_reset <= #1 wb_dat_i[2];
	end else begin
		rx_reset <= #1 0;
		tx_reset <= #1 0;
	end

// Modem Control Register
always @(posedge clk or posedge wb_rst_i)
	if (wb_rst_i)
		mcr <= #1 5'b0; 
	else
	if (wb_we_i && wb_addr_i==`UART_REG_MC)
			mcr <= #1 wb_dat_i[4:0];

// TX_FIFO or UART_DL1
always @(posedge clk or posedge wb_rst_i)
	if (wb_rst_i)
	begin
		dl[`UART_DL1]  <= #1 8'b0;
		tf_push   <= #1 1'b0;
		start_dlc <= #1 1'b0;
	end
	else
	if (wb_we_i && wb_addr_i==`UART_REG_TR)
		if (dlab)
		begin
			dl[`UART_DL1] <= #1 wb_dat_i;
			start_dlc <= #1 1'b1; // enable DL counter
			tf_push <= #1 1'b0;
		end
		else
		begin
			tf_push   <= #1 1'b1;
			start_dlc <= #1 1'b0;
		end // else: !if(dlab)
	else
	begin
		start_dlc <= #1 1'b0;
		tf_push   <= #1 1'b0;
	end // else: !if(dlab)

// Receiver FIFO trigger level selection logic (asynchronous mux)
always @(fcr)
	case (fcr[`UART_FC_TL])
		2'b00 : trigger_level = 1;
		2'b01 : trigger_level = 4;
		2'b10 : trigger_level = 8;
		2'b11 : trigger_level = 14;
	endcase // case(fcr[`UART_FC_TL])
	
//
//  STATUS REGISTERS  //
//

// Modem Status Register
always @(posedge clk or posedge wb_rst_i)
begin
	if (wb_rst_i)
		msr <= #1 0;
	else begin
		msr[`UART_MS_DDCD:`UART_MS_DCTS] <= #1 msi_reset ? 4'b0 :
			msr[`UART_MS_DDCD:`UART_MS_DCTS] | ({dcd, ri, dsr, cts} ^ msr[`UART_MS_CDCD:`UART_MS_CCTS]);
		msr[`UART_MS_CDCD:`UART_MS_CCTS] <= #1 {dcd, ri, dsr, cts};
	end
end

// Line Status Register

// activation conditions
assign lsr0 = (rf_count!=4'b0);  // data in receiver fifo available
assign lsr1 = rf_overrun;     // Receiver overrun error
assign lsr2 = rf_data_out[1]; // parity error bit
assign lsr3 = rf_data_out[0]; // framing error bit
assign lsr4 = (counter_b==8'b0); // break counter reached 0
assign lsr5 = (tf_count==5'b0);  // transmitter fifo is empty
assign lsr6 = (tf_count==5'b0 && (state == /*`S_IDLE */ 0)); // transmitter empty
assign lsr7 = rf_error_bit;

// lsr bit0 (receiver data available)
always @(posedge clk or posedge wb_rst_i)
	if (wb_rst_i) lsr0r <= #1 0;
	else lsr0r <= #1 lsr0;

// lsr bit 1 (receiver overrun)
reg lsr1_d; // delayed

always @(posedge clk or posedge wb_rst_i)
	if (wb_rst_i) lsr1_d <= #1 0;
	else lsr1_d <= #1 lsr1;

always @(posedge clk or posedge wb_rst_i)
	lsr1r <= #1 wb_rst_i ? 0 : // clear status on read
				lsr_mask ? 0 : lsr1 && ~lsr1_d; // set on rise

// lsr bit 2 (parity error)
reg lsr2_d; // delayed

always @(posedge clk or posedge wb_rst_i)
	if (wb_rst_i) lsr2_d <= #1 0;
	else lsr2_d <= #1 lsr2;

always @(posedge clk or posedge wb_rst_i)
	lsr2r <= #1 wb_rst_i ? 0 : // clear status on read
				lsr_mask ? 0 : lsr2 && ~lsr2_d; // set on rise

// lsr bit 3 (framing error)
reg lsr3_d; // delayed

always @(posedge clk or posedge wb_rst_i)
	if (wb_rst_i) lsr3_d <= #1 0;
	else lsr3_d <= #1 lsr3;

always @(posedge clk or posedge wb_rst_i)
	lsr3r <= #1 wb_rst_i ? 0 : // clear status on read
				lsr_mask ? 0 : lsr3 && ~lsr3_d; // set on rise

// lsr bit 4 (break indicator)
reg lsr4_d; // delayed

always @(posedge clk or posedge wb_rst_i)
	if (wb_rst_i) lsr4_d <= #1 0;
	else lsr4_d <= #1 lsr4;

always @(posedge clk or posedge wb_rst_i)
	lsr4r <= #1  wb_rst_i ? 0 :
			  lsr_mask ? 0 : lsr4 && ~lsr4_d;


// lsr bit 5 (transmitter fifo is empty)
reg lsr5_d;
wire tx_fifo_write;
assign tx_fifo_write = (wb_we_i && ~dlab && wb_addr_i==`UART_REG_TR);

always @(posedge clk or posedge wb_rst_i)
	if (wb_rst_i) lsr5_d <= #1 0;
	else lsr5_d <= #1 lsr5;

always @(posedge clk or posedge wb_rst_i)
	lsr5r <= #1 wb_rst_i ? 1 :
			(lsr_mask || iir_read || tx_fifo_write) ? 0 :  lsr5 && ~lsr5_d;

// lsr bit 6 (transmitter empty indicator)
reg lsr6_d;

always @(posedge clk or posedge wb_rst_i)
	if (wb_rst_i) lsr6_d <= #1 0;
	else lsr6_d <= #1 lsr6;

always @(posedge clk or posedge wb_rst_i)
	lsr6r <= #1 wb_rst_i ? 1 :
				 (lsr_mask || tx_fifo_write) ? 0 : lsr6 && ~lsr6_d;

// lsr bit 7 (error in fifo)
reg lsr7_d;

always @(posedge clk or posedge wb_rst_i)
	if (wb_rst_i) lsr7_d <= #1 0;
	else lsr7_d <= #1 lsr7;

always @(posedge clk or posedge wb_rst_i)
	lsr7r <= #1  wb_rst_i ? 0 :
			  lsr_mask ? 0 : lsr7 && ~lsr7_d;

// Frequency divider
always @(posedge clk or posedge wb_rst_i) 
begin
	if (wb_rst_i)
		dlc <= #1 0;
	else
		if (start_dlc | ~ (|dlc))
  			dlc <= #1 dl - 1;               // preset counter
		else
			dlc <= #1 dlc - 1;              // decrement counter
end

// Enable signal generation logic
always @(posedge clk or posedge wb_rst_i)
begin
	if (wb_rst_i)
		enable <= #1 1'b0;
	else
		if (|dl & ~(|dlc))     // dl>0 & dlc==0
			enable <= #1 1'b1;
		else
			enable <= #1 1'b0;
end

//
//	INTERRUPT LOGIC
//

assign rls_int  = ier[`UART_IE_RLS] && (lsr[`UART_LS_OE] || lsr[`UART_LS_PE] || lsr[`UART_LS_FE] || lsr[`UART_LS_BI]);
assign rda_int  = ier[`UART_IE_RDA] && (rf_count >= {1'b0,trigger_level});
assign thre_int = threi_clear ? 0 : ier[`UART_IE_THRE] && lsr[`UART_LS_TFE];
assign ms_int   = ier[`UART_IE_MS] && (| msr[3:0]);
assign ti_int   = ier[`UART_IE_RDA] && (counter_t == 10'b0);

reg 	 rls_int_d;
reg 	 thre_int_d;
reg 	 ms_int_d;
reg 	 ti_int_d;

// delay lines
always  @(posedge clk or posedge wb_rst_i)
	if (wb_rst_i) rls_int_d <= #1 0;
	else rls_int_d <= #1 rls_int;

always  @(posedge clk or posedge wb_rst_i)
	if (wb_rst_i) thre_int_d <= #1 0;
	else thre_int_d <= #1 thre_int;

always  @(posedge clk or posedge wb_rst_i)
	if (wb_rst_i) ms_int_d <= #1 0;
	else ms_int_d <= #1 ms_int;

always  @(posedge clk or posedge wb_rst_i)
	if (wb_rst_i) rls_int_d <= #1 0;
	else ti_int_d <= #1 ti_int;

// rise detection signals

wire 	 rls_int_rise;
wire 	 thre_int_rise;
wire 	 ms_int_rise;
wire 	 ti_int_rise;

assign rls_int_rise 	  = rls_int & ~rls_int_d;
assign thre_int_rise   = thre_int & ~thre_int_d;
assign ms_int_rise 	  = ms_int & ~ms_int_d;
assign ti_int_rise 	  = ti_int & ~ti_int_d;

// interrupt pending flags
reg 	rls_int_pnd;
reg 	thre_int_pnd;
reg 	ms_int_pnd;
reg 	ti_int_pnd;

// interrupt pending flags assignments
always  @(posedge clk or posedge wb_rst_i)
	if (wb_rst_i) rls_int_pnd <= #1 0; 
	else 
		rls_int_pnd <= #1 lsr_mask ? 0 :  						// reset condition
							rls_int_rise ? 1 :						// latch condition
							rls_int_pnd && ier[`UART_IE_RLS];	// default operation: remove if masked

always  @(posedge clk or posedge wb_rst_i)
	if (wb_rst_i) thre_int_pnd <= #1 0; 
	else 
		thre_int_pnd <= #1 thre_write || iir_read ? 0 : 
							thre_int_rise ? 1 :
							thre_int_pnd && ier[`UART_IE_THRE];

always  @(posedge clk or posedge wb_rst_i)
	if (wb_rst_i) ms_int_pnd <= #1 0; 
	else 
		ms_int_pnd <= #1 msr_read ? 0 : 
							ms_int_rise ? 1 :
							ms_int_pnd && ier[`UART_IE_MS];

always  @(posedge clk or posedge wb_rst_i)
	if (wb_rst_i) ms_int_pnd <= #1 0; 
	else 
		ti_int_pnd <= #1 fifo_read ? 0 : 
							ti_int_rise ? 1 :
							ti_int_pnd && ier[`UART_IE_RDA];
// end of pending flags

// INT_O logic
always @(posedge clk or posedge wb_rst_i)
begin
	if (wb_rst_i)	
		int_o <= #1 1'b0;
	else
		int_o <= #1 
					rls_int_pnd		?	~lsr_mask					:
					rda_int			? 1								:
					ti_int_pnd		? ~fifo_read					:
					thre_int_pnd	? !(thre_write & iir_read) :
					ms_int_pnd		? ~msr_read						:
					0;	// if no interrupt are pending
end


// Interrupt Identification register
always @(posedge clk or posedge wb_rst_i)
begin
	if (wb_rst_i)
		iir <= #1 1;
	else
	if (rls_int_pnd)  // interrupt is pending
	begin
		iir[`UART_II_II] <= #1 `UART_II_RLS;	// set identification register to correct value
		iir[`UART_II_IP] <= #1 1'b0;		// and clear the IIR bit 0 (interrupt pending)
	end else // the sequence of conditions determines priority of interrupt identification
	if (rda_int)
	begin
		iir[`UART_II_II] <= #1 `UART_II_RDA;
		iir[`UART_II_IP] <= #1 1'b0;
	end
	else if (ti_int_pnd)
	begin
		iir[`UART_II_II] <= #1 `UART_II_TI;
		iir[`UART_II_IP] <= #1 1'b0;
	end
	else if (thre_int_pnd)
	begin
		iir[`UART_II_II] <= #1 `UART_II_THRE;
		iir[`UART_II_IP] <= #1 1'b0;
	end
	else if (ms_int_pnd)
	begin
		iir[`UART_II_II] <= #1 `UART_II_MS;
		iir[`UART_II_IP] <= #1 1'b0;
	end else	// no interrupt is pending
	begin
		iir[`UART_II_IP] <= #1 1'b1;
	end
end

endmodule